[ Chinese wardrobe net ] Solid wood furniture has always been favored, so how much do consumers know about solid wood furniture? Is it blindly following the trend or knowing one or two?
At present, the solid wood furniture that is normally sold on the market and recognized in the industry refers to the plates used for furniture: solid wood wide panels, solid wood laminated materials and solid wood panels.
The following characteristics of the basic solid wood panels are based on standard processing techniques, qualified products for production and processing. Unqualified products that are shoddy, equipment, process, and materials are not up to standard are not discussed.
1. Solid wood furniture features
1 solid wood wide panel refers to the hardwood is processed into a narrow wooden strip (about 3-6cm, a small amount of wide wooden strips), and then horizontally splicing and splicing, and then sanding the upper and lower sides.
2 Solid wood laminated timber refers to a sheet made of narrow and short wooden strips which are made of adhesives (some of which are toothed), and then horizontally widened and sanded up and down.
3 solid wood panel refers to the narrowing of the narrow wooden strip with small material specifications, then the upper and lower surfaces are sanded, and then the hardwood and thin wood veneer with good pattern and good material are pressed on the upper and lower surfaces. Plate.
4 solid wood wide panel is basically the same as solid wood composite material, but because of the smaller material specifications, there are many lengthwise splicing.
5 The disadvantages of solid wood composite materials are often more prominent, and the advantages are far from being available. The amount of glue applied is much higher than that of solid wood wide panels.
2. Advantages
After the solid wood panels are painted, there is no unevenness on the surface of the rubber joints and slats, and the physical properties are relatively stable during long-term use.
The utilization rate of wood is high, which is in line with the principle of ecological utilization of raw materials. Therefore, in terms of use and texture color, solid wood panel decoration board is more suitable for the use of furniture and decorative functions.
Although the amount of glue applied to the solid wood panel is larger than that of the solid wood panel, the protection of the double-sided thick veneer and the edge of the four-side thick veneer are actually only two sides and eight sides of the glue joint, so the adhesive in the solid wood board is penetrated. The volatilized chemical substances are far lower than the volatilization of solid wood wide panels and solid wood laminated materials, which is more environmentally friendly and healthier.
Since the core plate is made of an anisotropic small wood, the surface of the plate is uneven and the degree of warpage is small, and the upper and lower sides are covered with two thin wooden veneers, which can better eliminate the unevenness and cracking of the plate surface. And can improve the physical strength of the board in all directions.
Sliced ​​thin wood veneer is a selection of high-grade logs of superior diameter, and is carefully selected according to texture and color, and is manufactured by high-precision equipment and scientific cutting method.
This kind of processing technology is very good in texture and color, and it has more outstanding texture after painting. The production of positive furniture can create a sense of harmony and high-grade value.
3. disadvantages
In addition, due to the different textures of the individual slats and the different hardness, even if the thickness of the slats is uniform, the thickness of each slat can be made uniform, so that the slats on the surface of the slab are uneven. After the paint, the unevenness of each slat is more obvious.
If the quality of the cross-stitch is poor, the brain will also spell out the obvious cross-stitch. If the strength of the cross stitch is not enough, it is easy to crack at the seam.
Therefore, the furniture produced by the general solid wood wide panel can see the surface of the furniture paint in the oblique direction, and can see the height of the slats and the glue joint between the slats. If the materials are selected and the technology is scientific, this phenomenon will be smaller, but it cannot be fundamentally avoided.
Due to the large anisotropy of the wood, the wide panel is easily deformed, and the glue joint between the panels is exposed, so that the disordered lines between the panels can be visually seen, and the firmness of the splicing has a great influence on whether the panel can be cracked. In addition, the painting process has the effect of moisture on the wood in the paint.
Even if the newly processed product is very flat, in the daily use, the surface of the solid wood wide panel is prone to uneven edges and cracks. These phenomena will become more apparent due to the humidity of the air over time. Moreover, the wider and thicker the substrate width of the panel is, the more obvious the problem is.
Such a process for making furniture sheets has high requirements for material selection, and the color, texture, and growth period of the panels are basic requirements, resulting in low utilization of wood, high waste, and high cost.
In particular, the growth period determines the degree of hardness of the wood, which directly affects the degree of deformation during use. This feature is almost indistinguishable from the well-painted household products, and only the brain bottle is used for a long time.
Even if the selection of materials is very strict, the production of large-faced furniture, such as countertops, door panels, etc., still lacks a sense of body, and the wood grain is slightly messy and cannot create a calm and gentle body atmosphere.
Square Box Tissue Paper,Square Box Facial Tissue ,Tissue Box Square Facial,Soft Square Box Facial Tissue
BODA ENTERPRISE LIMITED , https://www.bodapaper.com