[ Chinese wardrobe net ] Although the overall wardrobe installation looks quite difficult, there are many tools, but as long as the steps are followed by the installation, the installation of the whole wardrobe is very easy to get started. The following website will introduce the installation steps of the whole wardrobe and the precautions for the overall wardrobe installation.
Overall wardrobe installation steps
1. Cabinet installation:
Use a cloth to pad the floor, first assemble from the wide side panel against one end of the wall, and lay the wide side panel on the ground (maintaining 700mm spacing from the rear wall). First, put the plate of the filled three-in-one rubber plug on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link.
Then the solid layer is nailed to the cork, fixed on the wide side plate, the top handle with the large handle hole facing upward, the other solid layers are facing downward, and the foot line large handle hole is facing inward (the middle solid layer is consistent with the L frame height, that is, the bottom plate to the solid layer The inner space is 960mm, and the hole is drilled on site.)
Put the side panels, nail the cork, and the cork is required to connect the solid layers on both sides. Install the double-link on the second cabinet. Note that the double-handle can only lock half of the large handle, that is, 90°. When the two solid layers are fixed to the side plates, tighten the large handles at the same time.
2, nail back board:
Place the assembled whole cabinet on the floor of the point mat, and level the side panels into a uniform plane. Use a slider to measure the diagonal size of the cabinet and adjust it to the same level. Start with the first backing plate from the wide measuring board. Note that if there is a solid nail in the middle, draw the center line of the solid layer with a pencil and nail it. nail.
3. Installation of the L frame:
Use the side plates of the L frame to have a parallel line on the corresponding side plates, then move the 9mm upwards to draw the center line of the three-in-one rubber particles, and use the top frame of the L frame to draw a parallel line on the corresponding bottom plate, flat line The inner line of 9mm draws the center line of three rubber pieces. The hole was drilled with a 10 mm drill bit and the hole depth was 10-20 mm. Install a single pole. After the L frame is installed, nails are fixed on the back plate.
4. Three-section rail installation: the rails are placed against the drawers, flushing the drawer floor, and the moving female rail fixing sub-rail screws are mounted on the sub-track vertical eyes (this is an adjustable position). The interval between the two drawer panels to the center of the track eye is further increased by 2 mm. The data of the female rails is removed and the transverse line is drawn on the side panel of the cabinet with a 90° angle. The cross-sectional line is the central eyeliner of the female rail. .
The drawer panel is into the column, so the vertical cut line is drawn from the outer side of the side panel of the cabinet, the female rail is flush with the vertical tangent line, the central eye is flush with the horizontal line, and the screw is mounted on the transverse eye of the busbar (adjustable position). After the drawer is installed, the adjustable position is used for debugging, so that the drawer surface is flat and the gap is average.
Finally, the fixing screws are placed on the transverse eye of the sub-track and on the vertical eye of the female rail. And so on to install the next one. If you catch a full drawer, the same principle can be installed from bottom to top, and the top drawer can be fixed with a 90° angle. Conditions require that the face is leveled and the apprentice average. The drawer clearance is 2mm.
5, the grid rack installation:
Install the three-section track as the three-section rails, and measure the gap between the side plates and the center of the track plus 50mm gap. The data is drawn on the side panel of the cabinet to draw the transverse line, and the mother rail is installed for debugging and fixing. The upper side of the side panel of the lattice frame is fixed to maintain a 50MM gap for the purpose of facilitating the object.
6, pants rack installation:
Similar to the grid frame installation, the difference is that the side wall of the pants rack is 20mm away from the grid surface. Keeping the 20mm inner space is also convenient for use.
7, push-pull mirror installation:
The three-section rail is mounted on the push-pull mirror, and the height of the push-pull mirror is generally 1700 mm above the bottom solid layer (customer can request height). The rail transverse line is drawn on the side panel at a height of 90° according to the required height. The parallel spacing between the new eyes in the three-section track on the upper line is measured, and accurate data is obtained. The lower track transverse line is drawn on the side plate with a 90° square. Install the push-pull upper and lower mother rails, the mother rail is spaced 5mm apart from the back panel, and the push-pull mirror is attached.
8, the installation of Yitong:
Move the 38mm draw cross-cut line from the ground level, the side plate is divided into the vertical cut line, and the cross pad is the center position of the first eye above the clothing pass.
Overall wardrobe installation precautions
1. Check the work before installation, find the abnormality, and feedback in the first time to make corrections in time.
2. Carefully check the matching of the drawing identification with the site to determine the installation sequence.
3. Pay attention to the protection of the product assembly during the installation process.
4. Beam position, top line, and cut-off angle of the closing plate should be carefully checked and cut accurately.
5. Note that the hole surface of the side panel of the No. 4 cabinet should not be placed in the No. 4 cabinet.
6. When the nail backing plate is used, the diagonal of the measuring cabinet should be equal. If the solid layer is uneven, it should be flattened with a planing knife to nail the backing plate.
7. If the customer asks a question during the installation, it should be answered in time and the rationality of the disposal method should be informed.
8. If there is a problem with the installation, the installation worker must return to the installation note and return to the repair order to complete the tracking service.
9. After installation, you must first self-check, adjust, and then the customer acceptance, signature confirmation.
10. There must be a clean environment after the entire installation service process is completed.
11. If the cloakroom is high, install it from the inside out.
12. There is a top cabinet, the inside of the first cabinet, the lower cabinet and the upper cabinet are installed at the same time and then the lower cabinet is installed.
13. Adopt the vertical loading method, first and then the outside, from left to right and from right to left, the side panels are first connected to the main line, and the bottom line is fixed by the corner code. After the board, people have to climb out from the top cabinet. If the space in the top cabinet is too small, you can saw the back panel behind the drawer and then fix the back panel with the corner code.
14. There is an electric socket in the cabinet at the scene, which can be opened by the measuring ruler. The opening of the electric plug board is subject to the wall of the cabinet. If necessary, the electrical board can be mounted on the back panel without opening.
15. The solution for the top cabinet and beam cutting angle: first install the lower cabinet, saw the top cabinet board into the corresponding height, and place it on the side panel of the lower cabinet to take the spot ink as the quasi-saw angle.
16. The solution to the unevenness of the joint between the two closing plates and the top line. When making the first closing plate or the top line and adding a small board to the interface of the other board, expose 100-200mm, the purpose is to locate the board which is connected with it, and the small board can be fixed with 502 glue or screw.
17. If the drawer is loose and tight inside, the situation usually occurs when the nail back plate is not noticed, and the side plate is deformed. The hammer plate can be knocked out on the inner side of the side plate to restore the original shape.
18. When the gap between the door and the card door is large, there may be a deformation of the frame. The inner and outer door can be interchanged, and then the dust bar is added at the intersection of the two doors of the upper rail. If it is a full wooden door, The frame can be pressed down.
19. When the clothes on the upper cabinet exceeds two cabinets, the top and bottom plates are easy to be mixed: because the cabinets on the closet are made of different sizes, the top and bottom plates are not the same size, and the two sides are not the same width as the middle.
20. Deformation of the side panel of the closet: mainly the side panel of the closet is placed below the 2100mm of the light surface, and the fixed layer is placed. The side panel is in an empty state, and the door and the side panel are not tight. In the design, put a solid layer below 2100mm of the light side panel.
Nano Hydra Stamp,Lips Moisture Derma Stamp,Lips Derma Stamp,Nano Tip Derma Stamp
Guangzhou Vantee Electronic Technology Co., Ltd. , https://www.finerroller.com